Torque Measurement

Torque Measurement Detail Introduction

Today's torque measurement has been very widely used in various industries. There are some harsh environments, and if you need a relatively high-quality torque measurement device. I believe XIAO PENG is your trustworthiness.

Our torque measurement sensitivity and precision are very high. And the size is small, the weight is light, and the working state and stress distribution of the measurement have basically had no effect. And it can also adapt to a variety of complex environments if you need it. Welcome to us. Our customer service will provide 24h online service. No matter what questions you have, you can talk to us. Cooperate to promote the development of the industry!

Torque measurement
Torque measuring sensor process flow: Part assembly → Tit → low-frequency test → thermally stabilization processing → Protection → Shutdown → Patch → Welding → Replenish Zero Water drift → Makeup zero position → Pack.

Part assembly: Clean the end of the step, positioning pin, compression spring, and pillars with gasoline.
Tit: You should be labeled as required on the end of the elastomer.
Low-frequency test: After the elastomer is mounted on the grinding machine after the lengthened rod in the loader, the elastomer is removed after loading, and natural aging is 4 hours.
Heat stabilization: Eliminate the elastomer in the drying box in the oven at room temperature. After 8 hours after heating, then remove the elastomer to make it naturally cool.
Protection: The arc surface of the two patch planes and compensating pieces of the elastomer is protected.
Blowing: Sand treatment of the adhesive surface to enhance the effect of the patch.
Patch: Follow the rubber, scribing, packet, splice line terminal, and rub the wolf my class pen with acetone. Then use clean tweezers until there is no dust to fly out and the entire elastomer is cleaned with acetone. The two paste surfaces were washed with the degreasing cotton of alcohol, and the elastic body was flat. First, clean the paste surface with a clean silk cloth, and then use the steps to dry and dry.
Welding: The solder joint should be smooth, but it is not too large, the welding time is not more than one second, and finally, cleaning the solder joint.
Replenishing the zero-temperature drift: the zero-point temperature drift of the sensor is not more than 12UV / 10 ° C, and the solder joint is cleaned.
Mix zero: The zero drift measured in 10 minutes is no more than 5UV.
Puccubic: The rubber is carried out according to the steps such as glue, ginger, rubber, thermos, and allowed to dry.

The torque measurement sensor made by the above method is used, and the accuracy can reach more than 1 ‰, and the stability is good.

More explanation

XIAO PENG is a well-known instrument manufacturer in the industry. I have always adhered to my mission in the industry for many years. Basic principles for service customers. It is the target for more customers to provide high cost-effective torque measurement sensors. A beneficial help from customers in multiple countries and regions around the world.

For many years, XIAO PENG has mastered the most advanced production process. Represents the highest-end production level in the industry, using the highest quality raw materials and internationally renowned brands to produce equipment. All our devices are now. For example, analytical instruments, torque measuring equipment, displacement measurement instruments, etc., are passed CE certification. Have a very high-quality standard.

We have invested a lot of money every year to enhance our production process, including graduates who hired graduates from well-known universities at home and abroad to develop a suitable promotion mechanism for our original engineers. Solve their worries. Continuous training Our first-line production workers and active participation in social surveys. A series of initiatives provide a constant driving force for our company's development.

Under our engineers' continuous innovation. Our companies have become innovative enterprises. It has a significant contribution to torque measurement. Not only that, but XIAO PENG has also obtained a number of innovative awards and patents. Therefore, we also attracted many companies to invest. This further laid a solid foundation for the taking off of our company.

We can provide our customers with the highest cost-effective torque measurement equipment. In XIAO PENG, you don't have to worry about quality problems. Because all of our equipment is a material or production process, it has reached the world's leading level. Not only that but under our unremitting efforts. We also effectively control the production cost of torque measurement sensors. So we can not only provide torque measurement sensors with high precision and good stability. Also able to provide you with the best price.

If you have special needs, you can also contact us. We can also provide custom services. And after the warranty is waiting for your shopping trip to protect your shopping.

XIAO PENG adheres to the principle of customer-oriented. I adhere to our customers with high-cost torque measuring equipment. We sincerely invite you to come to our factory for a field inspection. At the same time, I sincerely look forward to working with you!

Torque Measurement: Complete Purchase Guide:

Do you have torque measurement? Do you need high-quality torque measuring sensors?
Here, some common questions about torque measurement and torque measurement sensors will be detailed below:

1. What is torque measurement?

The moment test is mainly divided into static torque and dynamic torque.
Dynamic Torque: Measurement of dynamic torque is generally involved in relative motion (mainly rotating). Because there is relative motion, the overall design is high for lead/signal processing and mechanical connection.
Static torque: This static means that the measured elastomer of the sensor does not participate in relative movement. Understanding from the force, such testing is the reaction of the elastomeric reaction force. It is common to secure the axis of the other end.

2. Benefits of Torque Measurement

1. Torque measuring device can measure dynamic torque and stationary torque. Moreover, the stability of the detection is excellent, the anti-interference performance is very strong, and the accuracy is very high.
2. When the device is measured, no need to zero and the positive and reverse torque can be continuously measured.
3. The signal output at the time of torque measurement can be freely adjusted, and the pulse wave, waveform-square wave, etc., can be selected freely.
4. The measurement range is wide: there are 0 to 1000 nm standards to choose from, some non-standard. For example, 20,000 nm, 100,000 nm, 1 million nm can be customized as a customized system.
5. Torque Measurement The volume of the sensor is very small. The heavy sensor can be used separately from the secondary instrument. When it is used, only the 15V and -15V power supplies are provided by the socket PIN. The frequency signal of the pulse wave or the like of the impedance or the like can be output. And it is very light and installed is very convenient.

3. Limitation of Torque Measurement

There are three main methods for torque measurement. Strain test torque method, capacitive torque sensor, laser torque sensor, anything is not perfect. These three torque measurement methods have various advantages and disadvantages.
Strain test torque method: There is a friction between the brush and the current ring, consumes high, the wear is faster, low service life, and the measurement accuracy is relatively low.

Capacitive torque sensor: The device is complicated, and it is more troublesome. Moreover, parasitic capacitance and distributed capacitance have a more significant impact on sensitivity and measurement accuracy.
Laser torque sensor: high production costs and costs are high. It isn't easy to promote use. The equipment is difficult to debug when performing the measurement, has poor orientation, and has a large temperature.

4. How Torque Measurement Works

The dedicated torch strain sheet was pasted on the measured elastic shaft and constituted a strain bridge. The electrical signal of the resilient axis can be measured to the strain bridge. After amplifying the strain signal, pass through the pressure/frequency conversion, becoming a frequency signal proportional to the torsion. The energy input and signal output of the system is undertaken by a special ring transformer with two sets of gaps, thus achieving contactless energy and signal transmission functions.

5. How to verify Quality of Torque Measurement

Torque measurements are required in many industries. The manufacturer of torque measuring sensors is also very much. Want to buy a torque measuring device of relatively high quality. It would be best if you learned to identify. Let's teach you the basic methods of three identification torque measuring equipment:

1. Look at the size of the torque measuring equipment manufacturers: The size of a company can see how the strength of this company is. And a powerful company can provide support services in all directions.
2. Look at the after-sales service of torque measuring equipment: XIAO PENG provides a complete after-sales service for our customers. Includes guidance and warranty services. You can solve all worries for yourself, let you buy the most cost-effective equipment.
3. Look at the production technology of torque measuring equipment: XIAO PENG introduces the most advanced production technology in the world. At the same time, the elements of internationally renowned brands were used. Represents the most advanced production level in the industry. The quality of the torque measurement sensor can be guaranteed.

6. industries Using Torque Measurement

Torque measurement is a very wide range of technologies. Almost various industries have applications. Common applications are as follows:
1. Torque in the operation of various machining centers and automatic machine beds.
2. Detect the output torque and power of rotational power equipment such as generator, motor, internal combustion engine.
3. Detect reducer, fan, pump, mixer, hoisting machine, propeller, drilling machine, etc., load torque, and input power.
4. Can be used to make a viscometer, electric torque wrench, etc.
5. Test the torque and efficiency transmitted by various rotational power equipment systems.
6. Detecting torque can detect speed and axial force.

7. How Much Torque Measurement Cost

Torque measurement technology is very wide to improve measurement accuracy further. Many customers are seeking a more superior torque measuring device. The price of torque measurement sensors in the market has a relatively significant difference. Its material and production processes mainly determine this.

Throughout all markets, the torque measurement sensor produced by XIAOPENG has a very high-cost performance. High precision is high, has long been used, and has smooth performance. It is also possible to use in harsh environments and is very superior. In addition, the price of the sensor is also very preferential. Because our engineers have effectively controlled production costs, they can give the best prices for customers.

We never blindly pursue the lowest price. We only provide customers with the highest cost-effective torque measurement equipment. In XIAO PENG although you can't get the lowest price on the market. But we can guarantee it. During this price range, our torque measurement equipment will be the highest.

8. Types of Torque Measurement in the Market

Torque measurement is very wide in various industries. The equipment used is a torque measurement sensor. Torque sensors, also known as torque sensors, torque sensors, torque sensors, torque gauges. It is mainly divided into two categories of dynamics and static, in which dynamic torque sensors can be called torque sensors, torque-speed sensors, non-contact torque sensors, rotary torque sensors, and the like.

9. Future of Torque Measurement

Since the range of torque sensors is now widely used, moreover, the market is getting higher and higher for torque measurement equipment. Therefore, the kit also has a very large development space. XIAO PENG summed upmarket experience through many years of development. We believe that the torque measurement equipment will develop in the following four directions:

1. Test system development towards miniaturization, intelligence, virtualization, and networking direction.
2. From single function to multi-function, including self-compensation, self-correction, adaptive, self-diagnosis, remote setting, status combination, information storage, and memory,
3. Develop in the direction of miniaturization and integration.
4. Developed from a static test to a dynamic online detection direction.

10. What is the advantage of choosing the torque measurement sensor of XIAO PENG?

XIAO PENG is an instrument manufacturer with years of development experience. Whether it is production experience or after-sales service, it is at the industry's leading level. We have a very powerful production capacity. Have highly automated production methods and experienced frontline workers. It can be guaranteed to deliver on time during the specified time. And we introduced the international advanced production technology and components of internationally renowned brands. Therefore, the torque measurement sensor produced has a very high-quality standard.

We have very competitive prices. Our engineers have passed many experiments. On the basis of controlling production costs, it will also be beneficial to our customers. Our goal is to help more customers get better development. Thereby achieving a win-win situation in cooperation. Finally, we also have a perfect after-sales service system. Any questions that occur during subsequent use. You can contact us. We will provide you with the most satisfactory solution.

Suppose you are looking for an ultra cost-effective torque measuring device. Or you have some questions about torque measurement. So contact us. XIAO PENG will be your most trusted partner!